Well, well, we all knew it had to happen. One of my copters crashed. It fell out of the sky, more then 30m onto asphalt. It looked really horrible. The Disco scattered into peaces, it had a totally broken frame with many damaged parts lying around. I could salvage a few pieces from the debris, but I will need to rebuild a new copter from scratch.
Luckily nobody got injured and nothing on the ground got damaged. So the worst thing is, that I don’t fully know why it happened. It could have been the almost empty battery, but I could also have been the camera controller board flying into the propellor. I guess I need to do more tests once I have rebuilt my Discovery. I just hoped I would not have to build a second Discovery Pro so soon again 🙁
In the third part of the build log I would like to cover the setup and configuration of the Taranis RC with the TBS Discovery Pro. After covering the mechanical build in part 1 and part 2 of the build log, this part will be about the wiring and programming of the remote control. Due to a crash I’ve build the copter a 2nd time.
Trekking on Mount Rinjani is a very popular activity on Lombok. With 3726 m (12’224 ft) above sea level, Rinjani is the second highest peak in Indonesia. The most popular access is from either Senaru or Sembalun. Trekking times vary depending on the route and destination. Wikitravel has a good article about it. I’ve chosen the 3 day / 2 night trip witch takes you to two locations on the crater rim, to the hot springs at the crater lake as well as to the summit. It is the most popular option, however there are also shorter tours which only take you to the crater rim.
We were especially unlucky with the weather. It was raining almost every day, which is very uncommon for the dry season. However, the wet season was just around the corner, starting in December, when trekking is not feasible anymore. With ponchos and backpack rain covers we tried to keep everything dry along the route.
The route is not technically difficult but it requires endurance. 8h+ of hiking every day and the total altitude difference of almost 3000m is not easy. I enjoyed the little challenge. With a normal level of fitness and a bit of preparation, everybody can do it. Most difficult was the final accent to the summit. The volcanic gravel stones make you slip backwards on every step and the thin air slows you down on top of it. But I made it and luckily there was even a bit of sunshine on the top. This was very rewarding after all the cold and wet hours to get there. But watch the video yourself I recorded with the Phantom on top of the Rinjani. I guess this is a world premiere. 😀
I’m just back from my trip to Indonesia, a beautiful country with big contrasts, lovely people and impressive volcanoes. On my journey in November 2013 I visited two islands, first Java and then Lombok. In my backpack I am not only carrying a GoPro but also the Phantom quadcopter 🙂 I thought it would be the perfect opportunity to take some great shots and videos at very unique locations. But please see yourself.
In the following days I would like to share with some of the nice spots I was visiting with the copter:
Ijen crater, a volcano and sulfur mine at the same time. I was there at night to catch the blue flames and inhale some nasty stinky sulfure clouds.
Mount Rinjani on Lombok. It is the second highest mountain in Indonesia with 3726m above sea level. We hiked all the way to the top in three days. Check out the video!
Gili Air, tropical island off the coast of Lombok with is great for snorkeling and relaxing.
I am still sorting through the Gigabites of photos and videos. Please be patient for the final videos to be edited and uploaded. But they are coming!
Advice for traveling trough airports
I had no problems at all at the airports in Indonesia. I guess they don’t really know what it is, but I also never had to open the bag for special inspection. I just followed the general ‘air travel’ regulations, which request, that you put the batteries into the carry-on (FAA rules). There are no regulations regarding the drone (electronics) itself. The airports in Europe and the bigger hubs in asia (e.g. Singapore) usually know the rules for batteries very well. The www.fpvlab.com forums are a great resource for travel reports, especially flying through exotic airports.
Packing the Phantom for air travel
I’ve put the phantom, remote and charger into the check-in bag. I removed the landing gear and propellors to fit it into a large backpack. The batteries and the GoPro went into the cary-on. I had no space for the Phantom there, but that should work too. In case they want to open your bag at security, always tell them first, that you have batteries inside. Sometimes, security personnel gets scared by the look of batteries.
Getting around in Indonesia with a drone
In Indonesia itself, people have rarely seen a drone. Therefore, they are mostly curious and a bit anxious at the same time. People ususally just watch from a distance, sometimes people start talking with each other. Sometimes they approach you. They are always friendly and just want to talk and find out what the white thing is that you bring and fly. When asked for the price of your toy, you might not want to give exact numbers to any stranger. Given the average daly income of $5 in Indonesia, your toy might look absurdly expensive.
When walking around / hiking, I had the phantom hanging off the backpack. In order to attract less people I usually put a rain-cover over the phantom, so people can’t see the drone. This makes it easier for you to get around without explaining to everyone what that white thing is you are carrying….
This is part 2 of the epic TBS Discovery Pro build. It got a bit delayed because I really wanted to show you the Leistkamm Video before finishing my second quadcopter. But now, back to the Discovery Pro.
After assembling the gimbal and motors and soldering the bottom plate in the TBS Discovery Pro build part 1, I put all the pieces together. It’s relatively straight forward to mount the four arms and red spacers to the bottom plate and then close up the sandwich with the top pcb plate. All the electronics and wiring is integrated into the frame and aside from the gimbal and controller, there are only a few cables connecting to individual parts. During the build I got to appreciate zip-ties for fixing all sorts of things, such as the electronic speed controllers (ESCs) onto the arms and the flight camera to the frame. The last piece I screwed on was the gimbal and it slides from the front.
At this point of the build I realized for the first time that something was a bit strange with the gimbal cables. I had to cross them to reach the appropriate connectors on the frame, which seemed a bit like a design flaw. But as it turned out later, I had misassembled the roll axis by 180 degrees, so the pitch motor facing the fpv camera instead of away from it. It took me until after the first power-up to realize this. The crossed cables lead to a second mistake: mixed up roll and pitch motors. The result of this is a hysterically spinning gimbal, rotating constantly as if were fully drunk. After fixing the gimbal orientation and connecting the motors into the correct pitch/roll connector everything was OK. The gimbal was level as expected. Wow, it looked cool!
I finished the ‘mechanical’ part of the build by adding more electronics, such as the video transmitter with the 5.8GHz cloverleaf antenna on the front right arm and the FrSky RC receiver X8R in the back on top.
More images in the build gallery. In the next part of the build log I will set up the Taranis RC radio and NAZA flight controller.
Hiking in Switzerland is great, but it’s even more fun if you bring you quadcopter! Enjoy this great video that I recorded along the hike from Arvenbühl up to the Leistkamm. Music Credits: Phase IV (lo-fi is sci-fi) / CC BY 3.0
For filming I used my stock Phantom quadcopter with a GoPro Hero3. The hike itself starts in Arvenbüel (1273 m) and takes about 2h40 to climb up to Leistkamm (2101 m) and another 2h to get down again. The view along the hike is very rewarding, especially on top where you are standing on a small rim. To the west is Lake Walensee, to the south you are looking along the Churfisten rim, of which Leistkamm is the most Northern one.
During the hike, I strapped the Phantom outside onto my backpack. Batteries and remote went inside. All in all it’s still pretty light and I can definitely recommend taking the Phantom with you all the time! So, stay tuned for more great videos from FPVblog.com
Today I would like to describe a workflow for natively handling high-frame rate videos with iMovie 11. I use this workflow to create super smooth slow motion scenes from 60fps or 120fps footage recorded with the GoPro. The following method uses iMovie 11 only with original videos straight from the camera. No additional software, plugins or other video pre-processing is needed. The trick is:
Import the videos straight from the camera or sd-card into iMovie 11 through the “Import from Camera…” dialogue.
In the next dialogue I then select Optimize video in Full – Original Size. The import takes quite some time, as the videos are transcoded while being imported. Once finished, the videos can be added to projects (such as 30fps NTSC). Without any additional transcoding the “Slow Motion” settings of the clip use the higher frame rate to make super smooth videos. Example slowdowns are 50% with a 60fps clip or even 25% on a 120fps clip.
Important: Any other import method will not work properly. The higher frame-rate will be lost if you add the exact same file through the general “Import” function or through the iPhoto library. This must be a bug or accidental feature of iMovie, depending on how you look at it. Have fun!